GWS Tool Group
Published

How The Income Tax System Works

You must read what follows, then pass it on to your friends. Save copies to give to your kids and grandkids.

Share

Leaders-In background

You must read what follows, then pass it on to your friends. Save copies to give to your kids and grandkids.

I did not write it; I wish I had. The author is T. Davies, Professor of Accounting at the University of South Dakota School of Business. It came to me in an e-mail. Here it is, word-for-word. 

“Let’s put [income] tax cuts in terms everyone can understand. Suppose that every day, ten men go out for dinner. The bill for all ten comes to $100. If they paid their bill the way we pay our taxes, it would go something like this:

“The first four men—the poorest—would pay nothing; the fifth would pay $1, the sixth would pay $3, the seventh $7, the eighth $12, the ninth $18, and the tenth man—the richest—would pay $59. That’s what they decided to do. The ten men ate dinner in the restaurant every day and seemed quite happy with the arrangement—until one day the owner threw them a curve (in tax language, a tax cut).

‘Since you are all such good customers,’he said, ‘I’m going to reduce the cost of your daily meal by $20.’ So now dinner for the ten only cost $80.

“The group still wanted to pay their bill the way we pay our taxes. So the first four men were unaffected. They would still eat for free. But what about the other six—the paying customers? How could they divvy up the $20 windfall so that everyone would get his ‘fair share?’ The six men realized that $20 divided by six is $3.33. But if they subtracted that from everybody’s share, then the fifth man and the sixth man would end up being PAID to eat their meals.

“So the restaurant owner suggested that it would be fair to reduce each man’s bill by roughly the same amount, and he proceeded to work out the amounts each should pay. And so the fifth man now paid nothing, the sixth pitched in $2, the seventh paid $5, the eighth paid $9, the ninth paid $12, leaving the tenth man with a bill of $52 instead of his earlier $59. Each of the six was better off than before. And the first four continued to eat for free.

“But once outside the restaurant, the men began to compare their savings. ‘I only got a dollar out of the $20,’ declared the sixth man, pointing to the tenth. ‘But he got $7!’

‘Yeah, that’s right,’ exclaimed the fifth man, ‘I only saved a dollar, too. It’s unfair that he got seven times more than me!’ ‘That’s true!’ shouted the seventh man, ‘Why should he get $7 back when I got only $2? The wealthy get all the breaks!’ ‘Wait a minute,” yelled the first four men in unison. ‘We didn’t get anything at all. The system exploits the poor!’

“The nine men surrounded the tenth and beat him up. The next night he didn’t show up for dinner (or, in the real world, he took his business out of the country), so the nine sat down and ate without him. But when it came time to pay the bill, they discovered, a little late what was very important. They were $52 short of paying the bill! Imagine that!

“. . . And that, boys and girls, journalists and college instructors, is how the tax system works. The people who pay the highest taxes get the most benefit from a tax reduction. Tax them too much, attack them for being wealthy, and they just may not show up at the table anymore. Where would that leave the rest? Unfortunately, most taxing authorities anywhere cannot seem to grasp this rather straightforward logic!”

The sad part is that we have not figured out how to beat the income tax. Earn and you pay; earn more and you pay more.

But happily, we do know how to beat the estate tax—legally. Join the tax-saving fun. To learn how, go to my Web site: www.taxsecretsofthewealthy.com.

Ingersoll Cutting Tools
Sumitomo
GWS Tool Group
Scientific Cutting Tools makes over 8,000 tools
IMCO
Iscar
Kyocera SGS
Horn USA
Techspex
Pat Mooney Saws
Hurco
KraussMaffei

Read Next

5 Rules of Thumb for Buying CNC Machine Tools

Use these tips to carefully plan your machine tool purchases and to avoid regretting your decision later.

Read More
Workforce Development

Building Out a Foundation for Student Machinists

Autodesk and Haas have teamed up to produce an introductory course for students that covers the basics of CAD, CAM and CNC while providing them with a portfolio part.

Read More

Registration Now Open for the Precision Machining Technology Show (PMTS) 2025

The precision machining industry’s premier event returns to Cleveland, OH, April 1-3.   

Read More
Sumitomo